The Dexter Trailer Hub and Drum Assembly - 5,200-lb E-Z Lube Axles # K08-201-98 comes with a single hub and drum.
So for a quantity of two you would need to enter "2" in the quantity box on the product page of the Dexter Trailer Hub and Drum Assembly - 5,200-lb E-Z Lube Axles # K08-201-98. view full answer...
Thanks for the info on your axle capacity, and we do have the correct hub and drum as well as self-adjusting brakes for a 5,200 lb Lippert axle, which I verified with the manufacturer, Lippert.
Starting with the hub and drum, the correct part depends on if you have an E-Z Lube axle (with a grease zerk) or not:
- Standard Axle: Dexter Trailer Hub and Drum Assembly - 5,200 lb Axles # K08-201-97
- E-Z Lube Axle: Dexter Trailer Hub and Drum Assembly - 5,200 lb E-Z Lube Axles # K08-201-98
Then... view full answer...
You are going to need to switch to a light like the LED Trailer Dome Light with Switch # 3375625337 as the Command Electronics 328-K-1020W light is obsolete. This light is 5-1/8" in diameter so it will be slightly larger than the 4-7/8" of the current light. view full answer...
We can get you set up with both the over/under kit and the hardware for your leaf springs. Thank you for the info on your axle capacity as it was exactly what was needed to get you the right kit, and since a 5,200 lb axle is 3 inches in diameter, the correct over/under is the following:
- Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00
Then for a suspension upgrade kit, by "serviceable shackle hardware" I believe you are looking for a wet bolt kit, and the best option for... view full answer...
Hey Josue, so I can't for sure identify what pin box you have on your camper but it does look like the standard Lippert 1621 that the Gen-Y part # GY58GR is designed to fit. If your current pin box is 12 inches wide and the distance between the front bolt holes and rear is 7-7/8 inches that would confirm this is correct fit. view full answer...
Did you mean 5,200 lb axles by chance? I only ask because I'm not aware of 5,700 lb axles, but either way the Dexter Over-Under Conversion Kits will work with your axles so long as it is either 2-3/8 inches or 3 inches in diameter and uses double-eye leaf springs (as opposed to slipper springs). Since a 2-3/8 inch axle is normally just for 3,500 lb axles, it is likely yours is 3 inches in diameter, but you will need to verify that to be sure. Here is what you will need, depending on your... view full answer...
Yes. It's not uncommon that over time, adhesives are affected by heat, humidity and exposure to the sun and UV rays; the Thinline Trailer Reflectors - Adhesive Backing - Screw Mount - Rectangle - Amber - Qty 2 # RE15AK aren't immune to this, unfortunately. However, when installing these I typically don't recommend relying only on the adhesive backing and that you also use a self tapping screw like the Screw - Self-Tapping Phillips Head - 8 x 3/4" # 1131832 to keep them firmly attached to... view full answer...
If the unloaded tongue weight of your 2015 Evergreen Ascend trailer is around 300 pounds, I don't think the Reese Pro Round Bar Weight Distribution # RE44FR is going to be the best option for you. This will have a minimum tongue weight rating of 600 pounds, which sounds like you would need to load the front of your trailer very heavy to get to.
With that said, it sounds like the better option will be the Reese Pro Round Bar Weight Distribution # RE34FR. This will have a tongue weight range... view full answer...
Thank you for the pictures!
To fit your 4400lb Lippert axles you will need Electric Trailer Brake Kit - Self-Adjusting - 12" - Left and Right Hand Assemblies - 5.2K to 7K # AKEBRK-7-SA which will replace the Lippert 122259 brake assemblies you have.
To verify which hub and drum assembly is correct for your trailer you will need to remove your hub and drum assembly and check the outer bearing numbers. If your bearings are worn to where you can't read the numbers, you will need to measure... view full answer...
While I don't know what equalizers came stock on your 2015 Evergreen 29QB LTD, I can still help you find the correct equalizers for your application.
What you'll need to do is take some measurements of your current equalizer. Measure the center-eye-to-center-eye of the side bushings and then from the top bushing straight down to where the middle of the lower bushings line up (see attached).
For the Equa-Flex Cushioned Equalizers # LC279688 you referenced those dimensions are 7-1/2" and... view full answer...
We have replacement motors for Solera/Lippert awnings that have a two pin connector like the part # LC373566. This is for awnings that were made after 2015. For awnings made before 2015 we have the part # LC266149. This uses two wires with spade connectors instead.
We don't offer any adapter harnesses but if you have something different you could pretty simply just use butt connectors to make the connection like the # DW05714. view full answer...
Your Jensen RV stereo can connect to the Jensen TV part # JTV4015DC. You can also connect Netflix and Hulu to it as well by using a Roku that would connect with an HDMI cable. view full answer...
We have just what you need in the # JWM60A as yes they have the same cut out size of 9" wide x 6" tall x 5-1/2" deep. The Jensen # JWM60A is actually a replacement for the older Jensen AWM965 stereo so this will work well for you. The wiring connector for the Jensen RV Bluetooth Stereo # JWM60A is the same as what it found on your existing stereo so you can simply plug in the connector from your old setup into the back of the new # JWM60A without splicing. I have attached an installation... view full answer...
Go To Results